Practical Encyclopedia Of Cutting Machine

In order to exert the good performance of the tape cutter, the user should check the wear of the blade in time after using it for a period of time. If the blade is found to be severely worn, sharpen it in time. When sharpening, due to the different methods of different people, but generally should be a
A basic principle is to sharpen the knife edge to balance. Also pay attention to the flatness of large trademark tape cutter blades. In the actual slicing process, the middle part of the blade is used more and the wear is serious. Therefore, pay attention to the balance of the tape cutter when sharpening, so as to avoid the crescent shape of the knife edge after using for a long time, which affects the quality of the slice.
 
Sharpening steps for large trademark tape cutter blades:
1. Place the blade on a rough surface test bench so that it will not run during the honing process.
2. Add an appropriate amount of thin lubricating oil or liquid paraffin on the grindstone surface and spread it evenly to increase the friction density.
3. Install the handle and holder on the slicing knife so that the cutting edge is forward and lay flat on the grindstone surface. Throughout the sharpening process, the worker's hands should be kept in place and pushed evenly and easily. Normally, hold the handle of the blade of the tape cutter with your right hand, hold the knife case with your left hand, and point the blade towards the front of the sharpener. Push the slicer diagonally forward from the lower right corner of the millstone to the upper left corner of the millstone Go to the heel and turn the blade from above. In the process of sharpening the knife, pay attention to the moderate degree of attention. It should be noted that in the process of sharpening the knife repeatedly, the tape cutter should be used.
 
Attention after mechanical belt cutter:
1. Turn the handwheel of the large label cutting machine, raise the specimen holder directly to the position, and turn the handwheel to stop the handle, and lock the specimen holder and the handwheel at the same time.
2. Then directly remove the cutting blade from the knife holder, wipe it and place it in the knife box.
3. Remove the specimen directly from the specimen clip of the trademark tape cutter manufacturer.
Fourth, clean up the cutting residue on the tape cutter.
Fifth, the whole machine is cleaned. Note: When using a slicing knife, we must be extra careful, because its blade is very sharp, if it is mishandled, it will cause serious injury. Do not directly touch the cutting blade with your hand, nor can you Random placement.
What are your concerns about computer tape cutters? Large-scale trademark tape cutting machine is a mechanical production automation equipment. Computerized tape cutting machine can make the traditional process of sewing with high speed and high power. It can also make the unachievable "multi-level, multi-function, uniformity. And perfection request, it is a multifunctional high-tech computer cutting machine. So what are the issues that everyone is worried about: uneven stitches, no after-sales guarantee, unaffordable price, simple operation, trademark cutting machine Can solve these troubles for you.
 
The computerized belt cutting machine adopts a lifting foot. When the height of the sewing material varies, the height of the presser foot can be automatically adjusted to ensure a smooth sewing effect. The plate-making device parts adopt high-definition LCD color screen, full Chinese display, support computer to make patterns, and the operation is simple and convenient. Save 3 times labor and improve work efficiency. Stability can adapt to various difficult movements. The company has a pre-sales and after-sales technical team free training package teaching package meeting, life-long maintenance of the nationwide warranty.
 
Features of crystal cutting machine:
First, the large label cutting machine is compact in the entire structure, so it is relatively small in area;
2. The atomization cooling method is adopted, and the whole cooling effect is good;
Third, the drum is very accurate;
Fourth, the trademark cutting machine uses multiple sets of scrapers, which is also more flexible in adjustment;
5. A side scraper is also installed to avoid the accumulation of material at the position of the drum at the side end;
6. The cutting machine uses a half-tube jacketed tray;
Seven, using the stepless speed regulation method, both the speed and the drum can be adjusted flexibly;
8. The whole scope of adaptation is wide, and the operation is flexible and simple;
Nine, with a variety of functions, can be sliced, can also complete the drying process. The cutting machine may encounter different abnormal phenomena in the working process. If it cannot be resolved in time, it will quickly affect the slicing effect and may also cause damage to the cutting machine.
 
Below I will introduce to you the common problems of large-scale trademark tape cutter manufacturers and the corresponding solutions. The cutting machine does not move smoothly. At this time, you can add lubricating oil to the moving shaft of the cutting machine. If the ambient temperature is lower than 0 ° C, inject low-temperature-resistant engine oil. At the same time, adjust the cutting machine moving Tighten the screws below the shaft. If there is vibration or slight noise during the operation of the trademark tape cutter, first check whether its workbench is stable and the machine is placed flat; then check whether the bolts of the machine are loose, check whether the lubricant in the moving part of the machine is used up, and check whether the blade is loose Wait. When the cutting machine is slicing, the machine is weak. It may be caused by the aging of its capacitor. Therefore, check the capacitor of the cutting machine and repair it in time according to the actual situation, so that the cutting machine returns to the normal and stable work .
The tape cutting machine produced by a qualified manufacturer can be used for multiple purposes. As long as it is equipped with different molds, it can produce products of different specifications, and the product has uniform density and high strength. The design of the belt cutting machine also has many advantages, such as its shell is made of plastic spray and stainless steel, and the cutter is made of steel, which is both wear-resistant and durable.
What is the problem with the cutting machine that can't stop the knife?
How to solve it:
1. The startup line of the trademark tape cutting machine is not normal: use an external power supply to power the tape cutting machine. Use a power meter to check whether the indication has changed. If there is no change, it is likely that the power cord is broken or the power button is in poor contact .
2. The power supply circuit of the battery is abnormal: Use an external interface to supply power to the tape cutter and see if it returns to normal when it is turned on. If it is normal, it is determined that the power supply circuit of the tape cutter is abnormal.
3. The IC of the power supply of the tape cutter is abnormal: Test the peripheral circuit of the power IC against the schematic diagram of the circuit to see if the test value is normal.
4. The system clock and reset of the trademark tape cutter are abnormal: You can use a dual total oscilloscope to test the CPU power of the tape cutter and check whether the waveform diagram during the reset is correct.
5. The logic circuit has a problem: that is, the failure of the tape cutting machine circuit board. Generally, this problem can be solved by repair welding.
6. Software conflict: If the installed software does not match the system of the tape cutter, it may also cause the tape cutter to fail to start. You can connect the tape cutter to the computer to delete the program.