The Application Of The Web Guide System Is Relatively Extensive.

The high-precision, high-speed, high-efficiency coil material automatic processing process of the guide system has higher and higher requirements for the control of the lateral position of the coil. Equipped with a high-performance automatic guide system is the key to improving the production capacity and yield of coils. The coil will produce lateral displacement (running deviation) during travel, unwinding and winding, so the guide system can be installed in the above three positions to control the precise passing of the coil.
     The system uses high-speed microprocessor, digital, modular, intelligent circuit design; advanced programming, user-friendly interface, LCD screen display; high-performance components and perfect circuit protection design to make the system run continuously and stably; control system response The time is less than 0.01 seconds; the accuracy of the system itself is up to 0.01mm. During the material winding process, the position of the edge or line is detected by the photoelectric sensor to pick up the edge correction frame or line position deviation signal. Then, the position deviation signal is transmitted to the photoelectric guide controller for logic operation, and a control signal is sent to the mechanical actuator to drive the mechanical actuator to correct the serpentine deviation of the material during operation to ensure linear motion of the material. Optional left and right limit switches prevent the system from running out of control.

The function of the guide system is relatively powerful, and it can perform the corresponding guide work well. Nowadays, the application of the guide system is relatively extensive, and its variety is widely used in many industries. Here is mainly to take the rectification system on the opposite side of the uncoiler as an example, briefly introduce:
This kind of guide system is a kind of system that combines light, machine, electricity and liquid. It uses high-tech products and has many functions. For example, its response speed is relatively fast, the measurement accuracy is also high, and the performance is relatively stable. Not so, its service life is also very long.
The stripping system of the strip is well controlled for unwinding and unwinding of steel and non-ferrous metals, etc. Its guiding performance is better, and it can be processed in color coating, pickling, continuous annealing and the like.
The reversing system on the opposite side of the unwinding is mainly a loop servo control system, which can test some predetermined targets accordingly. In addition, this servo control can convert the signal into high-power hydraulic energy, and let the cylinder move accordingly until it is adjusted.
These are the relevant introductions of this kind of correction system, and the scope of use of the guide system is constantly expanding.

Principles and requirements for daily mechanical maintenance of the guide system:
The routine maintenance of equipment is the basic work of equipment maintenance, and must be institutionalized and standardized. For the regular maintenance of equipment, work quotas and material consumption quotas shall be established, and assessment shall be carried out according to the quota. The regular maintenance work of equipment shall be included in the assessment content of the workshop contract responsibility system. Regular inspection of equipment is a planned preventive inspection. In addition to the human senses, the inspection methods must also have certain inspection tools and instruments. The inspections are carried out according to regular inspection cards. Regular inspections are also called periodic inspections. The mechanical equipment should also be checked for accuracy to determine the degree of accuracy of the equipment.
1. In order to ensure that the mechanical equipment is always in a good technical state, it can be put into operation at any time, reduce the downtime, improve the mechanical integrity rate, utilization rate, reduce mechanical wear, extend the service life of the machine, reduce the mechanical operation and maintenance costs, and ensure safe production. Maintenance of mechanical equipment must be intensified.
2. Mechanical maintenance must implement the principle of “maintenance and maintenance, prevention first”, and do regular maintenance and enforcement, and correctly handle the relationship between use, maintenance and repair, and do not allow it to be used only.
3. Each team must do all kinds of mechanical maintenance work according to the mechanical maintenance procedures and maintenance categories, and must not delay without undue delay. In special circumstances, it may be postponed for maintenance after being approved by the special engineer, but generally it should not exceed half of the specified maintenance interval.
4. Maintenance machinery should ensure the quality, according to the specified items and requirements, item by item, no leakage or no protection. The problems found in maintenance items, maintenance quality and maintenance should be recorded and reported to the department.
5. The maintenance personnel and the maintenance department should make “three inspections and one handover (self-inspection, mutual inspection, full-time inspection and one-time joint), and continuously summarize the maintenance experience and improve the quality of maintenance.
6. The Asset Management Department regularly supervises and inspects the mechanical maintenance of each unit, checks the quality of maintenance regularly or irregularly, and conducts awards and penalties.